Sam Gas Projects Pvt. Ltd.

Heat Reactivated Type Air Dryers are used when one needs compressed air of very low Dew point of (-) 60°C or (-) 80°C. In this design, the desiccant is regenerated at higher temperature, along with small quantity of Dry air purge. Due to purging with Dry air and thermal regeneration, residual moisture loading on desiccant becomes low and this gives very low Dew point. The Drying unit has 2-vessels filled with Activated Alumina or Molecular sieves desiccant. One vessel remains in drying cycle for 4 hours, while other vessel is simultaneously regenerated at atmospheric pressure. Around 3% flow of dryer capacity is used as purge for regeneration. Electrical heaters are provided in a central finned Stainless steel pipe in both drying vessels. Heating cycle is for 2 hours and in this time hot purge air increases desiccant temperature to around 100°C. At this temperature regeneration is complete (due to dry air purge). Dew point achieved is around (-) 40°C. If still lower Dew point is required, air purging rate is slightly increased to 5% for (-) 60°C and to 7.5% for (-) 80°C Dew point. SAM Gas Filters A Pre-filter with automatic drain valve is provided to remove any physical moisture from compressed air before entering Air dryer. A micronic filter is also provided in the Dryer outlet to arrest any desiccant dust particles, up to 1 micron size.

Salient Features

• Longer life of operation
• Requires less attention of operator
• Once installed can be operated automatically
• Heaters and valves are operated automatically
• Internal heaters provide maximum efficiency resulting in lower power requirement.
• Easy maintenance

A Heatless Type Air Dryers is the simplest form of gas or air dryer for achieving a dew point of -40 deg C or better for compressed air systems and other gas and air dryer applications.

Process: Wet incoming compressed air after passing through pre filter passes through the slide piston valve assembly and is directed towards absorber chamber i where the compressed air passes upward through the desiccant ( activated alumina / molecular sieves ). Compressed air drying takes place by adsorption. Dry compressed air from absorber chamber i then passes through the check valve assembly and then through the after- filter to the application or work area. while compressed air is being drying in chamber the desiccant in chamber where the desiccant has been wetted in the previous cycle is being simultaneously regenerated. The chamber is depressurized to atmosphere through the purge valve in the downward direction. A portion of the dry compressed air passes through the needle valve / orifice plate through the desiccant and flushes out the desorbed moisture. when the regeneration is complete, the purge valve is closed and the tower is slowly repressurise to line pressure for a smooth changeover. A drying period of 5 minutes provides an efficient dew point of -40o C or better (at atmospheric pressure ). In regeneration process approximately 30 seconds are required for repressurization.

In Heat of Compression Type Air Dryers, directly from Air compressor discharge is taken to Air dryer inlet through insulated pipelines, at 120o C (minimum) temperature. This hot air is passed through one drying vessel where saturated desiccant is regenerated by this hot air. After picking up moisture from desiccant bed, the air is cooled in an intermediate cooler. Here moisture is condensed and removed by auto drain valve. Cooled to 40o C, this air passes through the second drying vessel where balance moisture gets adsorbed and Dry air comes out. Cycle time is 4 hours regeneration & 4 hours drying. After 4 hours the changeover of vessels takes place automatically. In regeneration cycle heating of the bed is only 2 hours, and thereafter the bed is cooled by Dry air. After bed cooling, Dry air is again cooled to 40o C in another cooler, and delivered out of unit as Dry air at 40o C temp. The Dryer is fully automatic with pneumatically actuated Ball/ plug valves. A sequence timer controls operation of these valves. Desiccant used is Activated Alumina and it dries the air up to (-) 40o C Dew point.

Salient Features

• Easy maintenance
• Trouble free operation
• Longer life of desiccants
• Fully automatic operation
• Low pressure drop
• Highly efficient as there is no loss of compressed air

We manufacture a wide range of Refrigerated Type Air Dryer. The Basic principle is the removal of moisture by cooling air to certain present temperature.

The concept of efficient cooling is removal of heat only. The air first enters into the pre-cooler where the incoming hot air is being cooled by outgoing cold air so as to reduce the heat load of evaporator.The air from pre-cooler enter into the evaporator where further heat is removed by boiling refrigerant like Freon.

Now the air get condensed and this moist air is passed through a moisture separator where moisture is drained out by centrifugal action of air. The moist free air enters into pre-cooler to cool the incoming air.

Features :

• Simple and compact design.
• Automatic cleaning of the condenser.
• Efficient Power Saving.
• Least pressure drop.
• Easy maintenance.

Capitalizing on our in- depth industry knowledge, we offer a wide range of No Purge Loss Type Air Dryers, These are used for removing water vapor without the loss of compressed air. Our range is offered in different capacities, pressure and dew point as per the client’s requirement. We ensure to test the entire range on well-defined parameters to deliver the defect free and high performing dryers to the end users.

Our company has achieved widespread recognition for Air Dryer. These products are designed in close adherence to clients specifications, our products have achieved huge requirement in highly competitive market. These products designers assure that the range is developed using quality-checked material according to the set industry standards.

Features:

• Less maintenance
• High performance
• Energy efficient